Rip enhancements for ipv6, detailed in rfc 2080, include support for ipv6 addresses and prefixes. If the version command is omitted then the router defaults to sending ripv1 but can receive both ripv1 and ripv2. Ipv6 rip functions the same and offers the same benefits as rip in ipv4. Rip cisco, aprende a configurar este protocolo facilmente. Routing information protocol rip is a dynamic routing protocol which uses hop count as a routing metric to find the best path between the source and the destination network. The version command is used to specify which rip version to use either 1 or 2. Verifying rip routing configuring rip is pretty easy, especially in small networks. Protocole rip version 2 s2c7 protocole rip version 2. The version field contains a value of 1 for rip1 message and 2 for rip 2. Veamos como configurar ripv1 o v2 en packet tracer. Cisco implementation of ripv2 supports two modes of authentication. Due to some deficiencies in the original rip specification, rip version 2 was developed in 1993.
This article concentrates on the enhanced routing information protocol, also known as rip version 2. Sample configuration for authentication in ripv2 cisco. The routing information protocol rip is one of the oldest distancevector routing protocols. This document shows sample configurations for authenticating the routing information exchange process for routing information protocol version 2 ripv2.
How to configure routing information protocol rip, routing information protocol version 2 ripv2 lab practice if you are not familiar with routing information protocol rip, click the following link to view an introduction to routing information. Due to the deficiencies of the original rip specification, rip version 2 ripv2 was developed in 19934, published as rfc 1723 in 1994, and. Rip version 2 rip2, is a classless routing protocol. Ripv1 rfc 1058 is classful, and thus does not include the subnet mask with its routing table. It supports classless interdomain routing cidr and has ability to carry subnet information, its metric is also hop count and max hop count 15 is same as rip version 1. The routing information protocol rip is one of the oldest distancevector routing protocols which employ the hop count as a routing metric. Analisis y evaluacion del routing information protocol rip.
Rip configuration s2750, s5700, and s6720 v200r008c00. From the 2600a router, use the show ip route command to verify the routing table. It is important to be able to verify rip on cisco routers. This document specifies a routing protocol, based on the routing information protocol rip, as defined in 1, 2, for the simple internet protocol sip, as defined in 3. Ripv2 routing information protocol cisco community. Version 1 was designed only with 32bit counters which can store integer values from zero to 4. Tcpip routing information protocol rip, rip2 and ripng. Rfc 1723 rip version 2 carrying additional information. Libros y otros recursos rfc1058 routing information protocol rfc1721 rip version 2 protocol analysis rfc1722 rip version 2 protocol applicability statement rfc1723 rip version 2 carrying additional information rfc2082 rip 2. Snmp version 2 introduces the option for 64bit data counters. Posted on 6 junio, 2011 actualizado enn 3 marzo, 2012.
Rip aun es popular debido a su simplicidad y amplia compatibilidad. It support authentication and does subnetting and multicasting. Ip rip routing information protocol comes in two different versions. Cisco ios, uses router rip command to enable rip routing protocol. Tcpip routing information protocol rip, rip 2 and ripng the most popular of the tcpip interior routing protocols is the routing information protocol rip. Rip1 supported subnet entries only within the subnetted network.
1453 856 255 917 652 587 692 1264 80 1354 295 717 962 1202 788 1030 1174 465 1107 1535 413 1548 1100 130 464 786 1453 1303 59 442 1415 297 1237 12 1388 1420 706 1062 787 1213 379 1054 252 745 618 920 941 1388